Then why do you think manufacturers still list these failure rates (to be sure, it is marked as a limit, not an actual rate)? I’m not being sarcastic or facetious, but genuinely curious. Do you know for certain that it doesn’t happen regularly? During a scrub, these are the kinds of errors that are quietly corrected (althouhg the scrub log would list them), as they are during normal operation (also logged).

My theory is that they are being cautious and/or perhaps don’t have any high-confidence data that is more recent.

Bit error rates have barely improved since then. So the probability of an error whenr reading a substantial fraction of a disk is now higher than it was in 2013.

But as others have pointed out. RAID is not, and never was, a substitute for a backup. Its purpose is to increase availability. And if that is critical to your enterprise, these things need to be taken into account, and it may turn out that raidz1 with 8 TB disks is fine for your application, or it may not. For private use, I wouldn’t fret. but make frequent backups.

This article was not about total disk failure, but about the much more insidious undetected bit error.

Let’s do the math:

The error-reate of modern hard disks is usually on the order of one undetectable error per 1E15 bits read, see for example the data sheet for the Seagate Exos 7E10. An 8 TB disk contains 6.4E13 (usable) bits, so when reading the whole disk you have roughly a 1 in 16 chance of an unrecoverable read error. Which is ok with zfs if all disks are working. The error-correction will detect and correct it. But during a resilver it can be a big problem.

I also use this, and it works great. Another downside is that when using the free service, others can just use subdomains of your registered domains. You can always deny it, but you have to do it manually. With the premium subscriptions you can prevent that automatically for a number of domains, depending on how much you pay.

To add, unlike “traditional” RAID, ZFS is also a volume manager and can have an arbitrary number of dynamic “partitions” sharing the same storage pool (literally called a “pool” in zfs). It also uses checksumming to determine if data has been corrupted. On redundant setups it will then quietly repair the corrupted parts with the redundant information while reading.

ebay is very international, and is also by far the greatest site for second-hand stuff in most European countries. I normally buy my used drives there.

mixing drive models is certainly not going to do any harm

It may, performance-wise, but usually not enough to matter for a small self-hosting servers.

Sure, SCSI disks will show their defective list (“primary defects”, as delivered by the factory, and grown defects, accumulated during use), and they all have a couple hundred primary defects. But I don’t see why that would affect the reported geometry, given that it is fictional, anway. And all disks have enough spare tracks to accommodate for the defects, and offer the specified full number of total sectors, even for long list of grown defects. Incidentally, all the 4TB disks are still “perfect” in that they have no grown defects.

And yes, ever since LBA, nobody has used sectors and cylinders for anything.

I’m not touching that post again. But a small rant about typesetting in lemmy: It seems there is no way whatsoever to put angle brackets in a “code” section. In an overzealous attempt to prevent HTML injection, everything in angle brackets is just removed when posting (although it remains there in preview). In normal text, you can use “<”, but not inside “code” segments, where it will be retained verbatim.

If you’re as paranoid as me about data integrity, SAS drives on a host adapter card in “Initiator Target” (IT) mode with write-cache on the disks disabled is the safest. It will degrade performance when writing many small files concurrently, but not as badly as with SATA drives (that’s for spinning disks, of course, not SSD). With a good error-correcting redundant system such as ZFS you can probably get away with enabled write cache in most cases. Until you can’t.

RAID is generally a good thing but don’t get complacent, follow the 3-2-1 method

To expand on that: Redundant drive setup and backups serve completely different purposes. The only overlap is in case of a single disk failure, where RAID (or similar) may save the data.

Redundancy is all about reducing downtime in case of single hardware failures. Backups not only protect you from data loss in case of multiple simultaneous failures, but also from accidental deletion. Failures that require restoration of data almost always involve downtime. In short: You always need backups (unless it’s strictly a local cache, and easily recreatable), but if you want high availability, redundancy may help.

3-2-1-rule for backups, in case you’re unfamiliar: 3 copies of important data, on 2 different media, with 1 off-site.

If you want a proper server, it seems that Asrock Rack is the only manufacturer of AM4-socket-based server mainboards. Unlike desktop/gamer boards, these are designed for parallel airflow, typically from front to back in a 19" rack. These also come with IPMI remote maintenance, so can be operated headless in a remote location.

I have considered one of these for a while, such as the X570D4U, which also supports up to 128 GB of ECC RAM. Depending on what you want, this may be overkill, though.

(This was my favourite, because it has two M.2 slots, but there are others with only a single slot, since you said you only need one.)

Unlike gamer or other boards, these have no fancy black vanity covers and often won’t allow overclocking, but are typically very well designed and rock solid for unattended 24/7 operation.

Thanks.

Thanks. Right now I’m away from the machine so can’t look, but I’ll keep an eye open for a T420 mainboard and a second CPU, then. It’ll still be a decent machine, I think, with two E5-2470 V2. DDR3 ECC-RAM is also dirt cheap these days.

Clearly you neither read my post nor looked into what the air baffle in the T320 actually looks like. So whats your point?

It’s much more than a fan shroud. It’s a baffle specifically designed to guide cooling air over the CPU heatsinks and the RAM modules. This kind of airflow design is very common in servers. I wouldn’t trust it without, especially since the CPU heatsinks have no dedicated fans, but rely on the aerodynamic functioning of the baffle.

And yes, I know they are very similar, in fact I am quite (but not absolutely) certain that they are identical except for the actual second CPU socket. It’s almost as if you didn’t read my post. Even the soldering points for the second CPU socket are there in the single-CPU T320. They certainly won’t have different PSU connectors. They even share part numbers for the case.

I’d have to check the baffle shape again. But thanks for the insight.

What’s your problem with DAVx^5? It’s completely and permanently free and fully-featured on f-droid. Only the PlayStore version costs money. The authors don’t want to make money, but motivate you to move away from Google infrastructure.

If you only need address/phone number sync, then nextcloud is probably overkill, but I use it, and it works great. Also for calendar sync and file storage.

(You don’t need to put the community name in the title, especially not with “@”, which signifies usernames. Communities are prefixed by “!”.)

As to filling up the drives so fast, have you considered transcoding it to a smaller format (such as HEVC/H.265) in real time? I know that would require quite some CPU power. Even H.264 is likely to improve on camera native formats, as those often need to encode the videos with embedded/low-power CPUs. Do you need to retain the footage beyond 3 months?